CMS-Flow:Equilibrium Bed load plus AD Suspended load: Difference between revisions

From CIRPwiki
Jump to navigation Jump to search
No edit summary
No edit summary
Line 66: Line 66:


<table border>
<table border>
<tr width=100%>
 
<td>Table 1<br>Features of Calculation of Pick-up and Deposition Rates</td>
<tr>
<td>Table 1 Features of Calculation of Pick-up and Deposition Rates</td>
</tr>
</tr>


<tr><td>Method</td><td>Reference Concentration</td><td>Conversion Parameter</td><td>Comments</td>
<tr><td>Method</td><td>Reference Concentration</td><td>Conversion Parameter</td><td>Comments</td>
</tr>
<tr>
<td>Exponential Profile</td><td>Eq. 90</td><td>Eq. 104 and 105</td><td>Fast computation.  Tends to overestimate sediment transport rate. Can be used for some tests.</td>
</tr>
<tr>
<td>Van Rijn Profile</td><td>Eq. 90</td><td>Solves Eq. 85 numerically with
Eq. 103 (Runge-Kutta 4<sup>th</sup>)</td><td>Requires substantial computing time. Provides the same results as van Rijn (1985).</td>
</tr>
<tr>
<td>Lund-CIRP Profile</td><td>Eq. 70</td><td>Eq. 104 and 72</td><td>Fast computation. Newly developed sediment transport formula.
</tr>
</tr>



Revision as of 19:12, 23 October 2014

Equilibrium Bed load plus Advection-Diffusion Suspened load Transport model

Transport Equation

The transport equation for the suspended load is given by

 

(1)

Bed Change Equation

If the advection-diffusion (A-D) equation is selected to simulate the sediment transport and mixing, the change in the water depth is calculated by the sediment continuity equation

 

(2)

where is the sediment porosity, and is a bedslope coefficient.

Pick-up and Deposition Rate

The AD model calculates the bed level change due to suspended load from the difference between pick-up rate and deposition rate in Equation 80. The pick-up rate and the deposition rate are also applied as the bottom boundary condition in Equation 79. The boundary conditions are specified at an arbitrary level above the mean bed level:

  (3)
  (4)

where c = equilibrium concentration of suspended sediment at a given elevation, and z = vertical coordinate. Both ca and c0 are reference concentrations defined at z = a. Because the upward flux of sediment depends on the bed shear stress, ca is determined from the bed shear stress calculated from the local hydrodynamic conditions. Representation of ca within CMS-M2D is dependent on selection of either the van Rijn or Lund-CIRP models. The downward sediment flux depends on the concentration in the upper water column; therefore, c0 is specified from solution of Equation 79.

Assuming that the suspended concentration is in equilibrium then the basic equation for suspended sediment concentration can be written:

  (5)

This equation can be solved analytically by applying an appropriate mixing coefficient , and the vertical profile of suspended concentration is obtained in the following form:

  (6)

where F(z) is a function of the vertical concentration distribution. The relationship between the reference concentration c0 and the depth-averaged concentration C is:

  (7)

Thus, c0 may be written in the following form by introducing a conversion function :

  (8)


The bed level change due to suspended load is based upon the difference of the two types of reference concentration:

  (9)

This equation implies that erosion occurs if ca > c0, and accretion occurs if ca < c0.

In the AD model, three methods of specifying ca and c0 (that is, ) are implemented. Two of the methods are based on the van Rijn formula (van Rijn 1985) and one on the Lund-CIRP formula (Camenen and Larson 2006). Table 1 summarizes general features of the methods.

van Rijn formula

  (10)

where a = reference height and = maximum bed shear stress given by Equation 38.

Table 1 Features of Calculation of Pick-up and Deposition Rates
MethodReference ConcentrationConversion ParameterComments
Exponential ProfileEq. 90Eq. 104 and 105Fast computation. Tends to overestimate sediment transport rate. Can be used for some tests.
Van Rijn ProfileEq. 90Solves Eq. 85 numerically with Eq. 103 (Runge-Kutta 4th)Requires substantial computing time. Provides the same results as van Rijn (1985).
Lund-CIRP ProfileEq. 70Eq. 104 and 72Fast computation. Newly developed sediment transport formula.


Boundary Conditions

There are three types of boundary conditions in the sediment transport: Wet-dry, Outflow and Inflow.

1. Wet-dry interface.

The interface between wet and dry cells has a zero-flux boundary condition. Both the advective and diffusive fluxes are set to zero at the wet-dry interfaces. Note that avalanching may still occur between wet-dry cells.

2. Outflow Boundary Condition

Outflow boundaries are assigned a zero-gradient boundary condition and sediments are allowed to be transported freely out of the domain.

3. Inflow Boundary Condition

When flow is entering the domain, it is necessary to specify the sediment concentration. In CMS-Flow, the inflow sediment concentration is set to the equilibrium sediment concentation. For some cases, it is desired to reduce the amount of sediment entering from the boundary such as in locations where the sediment source is limited (i.e. coral reefs). The inflow equilibrium sediment concentration may be adjusted by multiplying by a loading scaling factor and is specified by the Advanced Card:
   NET_LOADING_FACTOR <white space> #
where # is the loading factor in dimensionless units.

References

Buttolph, A. M., C. W. Reed, N. C. Kraus, N. Ono, M. Larson, B. Camenen, H. Hanson, T. Wamsley, and A. K. Zundel. (2006). “Two-dimensional depth-averaged circulation model CMS-M2D: Version 3.0, Report 2: Sediment transport and morphology change.” Coastal and Hydraulics Laboratory Technical Report ERDC/CHL TR-06-9. Vicksburg, MS: U.S. Army Engineer Research and Development Center, U.S.A.

Camenen, B., and Larson, M. (2007). “A unified sediment transport formulation for coastal inlet application”. Technical Report ERDC-CHL CR-07-01. Vicksburg, MS: U.S. Army Engineer Research and Development Center, U.S.A

Soulsby, R. L. (1997). "Dynamics of marine sands, a manual for practical applications". H. R. Wallingford, UK: Thomas Telford.

Watanabe, A. (1987). “3-dimensional numerical model of beach evolution”. Proc. Coastal Sediments ’87, ASCE, 802-817.

Wu, W. (2004).“Depth-averaged 2-D numerical modeling of unsteady flow and nonuniform sediment transport in open channels”. J. Hydraulic Eng., ASCE, 135(10), 1013–1024.

van Rijn, L. C. (1985). “Flume experiments of sedimentation in channels by currents and waves.” Report S 347-II, Delft Hydraulics laboratory, Deflt, Netherlands.

Zhu, J. (1991). “A low diffusive and oscillation-free convection scheme”. Com. App. Num. Meth., 7, 225-232.

Zundel, A. K. (2000). “Surface-water modeling system reference manual”. Brigham Young University, Environmental Modeling Research Laboratory, Provo, UT.

External Links

  • Aug 2006 Two-Dimensional Depth-Averaged Circulation Model CMS-M2D: Version 3.0, Report 2, Sediment Transport and Morphology Change [1]
  • Aug 2008 CMS-Wave: A Nearshore Spectral Wave Processes Model for Coastal Inlets and Navigation Projects [2]



Documentation Portal