Culverts

From CIRPwiki
Revision as of 18:09, 19 September 2010 by Deleted (talk | contribs)
Jump to navigation Jump to search

Representation of Culverts in the CMS

By Christopher Reed and Alejandro Sánchez

Last Modified: September 17, 2010

Introduction

Culverts are a common coastal structure used to increase flushing improve water quality and also provide passage for fish and other aquatic animals to coastal lagoons and bays. The implementation of culverts is based on equations developed by Bodhaine (1982). In coastal applications of culverts, the culverts often connect open water bodies of similar water surface elevation, for instance, to enhance flushing or provide controlled flow through levees or causeways. Therefore, the implementation of culverts assumes sub-critical flow conditions. The implementation of culverts in the CMS is validated in two applications on the lower Mississippi River. The culvert feature is validated with an application to optimize discharges in simulations of the White Ditch diversion in Plaquemines Parish, Louisiana.

Formulation

Figure 1. Schematic showing culvert flow conditions.

The representation of culvert flow in the CMS is based on the approach of Bodhaine (1982) and is applied for circular and rectangular culvert cross-sections. Bodhaine describes six types of flow conditions through a culvert that depends on the culvert slope and the upstream and downstream water levels. In most coastal applications of culverts, they are level and the water elevations on either side are similar. These conditions can be considered as ponded upstream and downstream conditions and are most similar to Bodhaine Type 4 flow conditions. A schematic of the typical flow conditions for the culvert is shown in Figure 1. Assuming that the entrance and exit losses are small compared to friction losses in the culvert, the flow equations can be derived from Manning’s equation (using the metric system):

  (1)

where is the flow through the culvert, is the flow cross-sectional area, is the hydraulic radius, is the hydraulic gradient, and is Manning’s.

Coefficient has been introduced to allow for calibration or representation of other losses. If calibration data is not available then the coefficient should be set to 1.0.

The hydraulic gradient S is defined as:

  (2)

where the variables , , and are defined in Figure 1.


The hydraulic radius is defined as the flow area divided by the wetted perimeter . The values for these variables are dependent on the culvert cross-section and the water depth in the culvert.

Circular Cross-section

Figure 2. Variable definition for circular cross-section.

For circular culvert cross-sections, using the definitions in Figure 2, the wetted perimeter and flow area are:

and (3)

where and

Rectangular Cross-section

Figure 3. Variable definition for rectangular cross-section.

For a rectangular cross-section the wetted perimeter and flow area are:

and (4)

where the variables defined as shown in Figure 3.

Flap Gates

The option for including a flap gate at one end of the culvert is also included. For this implementation, flow is limited to the ’downstream’ direction only. If the hydraulic gradient opposes the designated downstream direction (i.e.< 0), the flow is set to zero.

Numerical Implementation

Figure 4. CMS grid and designation of culverts.

The CMS-Flow explicit model uses a staggered grid for the basis of the numerical solution. Two examples of a culvert implementation on the CMS grid are shown in Figure 6. The beginning and end of the culvert are not restricted to adjacent cells and can cross multiple active or inactive cells. A culvert is specified by an upstream and downstream cell, the culvert invert elevation (relative to the model datum), the culvert coefficient

and the culvert shape (circular or rectangular) and associated parameter values. For circular cross-sections, the culvert radius r is specified, and for rectangular cross-sections, the width w and height d are specified. If a flap gate is specified, the flow is limited to the downstream direction. Thus, the upstream and downstream cell designation are important when flap gates are included. The momentum flux of flows through the culverts are assumed to be small and not included in the momentum balance calculations in the CMS solvers. Thus, the culvert flows are only included in the mass balance calculations in the CMS solvers.


Culverts and weirs can be associated with the same CMS cell face and the total flux across the cell face will be the sum of all weirs and culverts specified for that cell face. However, only the fluxes associated with the weirs will be included in the momentum balance.


When salinity or sediment transport is included in simulations with weirs or culverts, the salinity and suspended sediment will be transported. The bedload components in sediment transport algorithms will not be transported over weirs and through culverts.

Example Application

Figure 5. Culverts designated for Alternative Location 2.

Located southeast of New Orleans on the coast of Louisiana, the White Ditch area has been experiencing the shortage of fresh water, sediments and nutrients from the Mississippi River, and saltwater intrusion due to sea level rise and storms. As a result, extensive wetland loss and degradation of tidal marshes has occurred in the area through the years. A hydrodynamic and salinity modeling analysis was conducted by URS (2010) to evaluate alternative designs for a fresh water diversion from the Mississippi River to the project area. The alternatives were evaluated in terms of their impact on water depths and salinities throughout the study area.


Two alternative locations (Locations 2 and 3) are proposed for the diversion near White Ditch. Location 2 uses a modification of the existing siphon at White Ditch. Location 3 is located farther to the south. At both alternative locations different channel depths and widths are considered for different peak diversion flow rates, ranging from 5,000 to 100,000 cfs. Location 2 also includes culverts located throughout the modified channels to provide connectivity with the marsh areas.


The alternative design at Location 2 is connected to the Mississippi River with a box culvert and consists of two main outfall channels and three distribution channels, as indicated in Figure 10. The channels are flanked by levees that constrain the flow within the channels until reaching the downstream ends of the channels. Culverts are distributed along the channels to provide connectivity to the wetlands, and plugs are placed at some junctures to control the flow.


At each of the two alternative locations, six design diversion flow rates were considered. For each flow rate a different channel cross-sectional area was used. The number of culverts was also varied at Location 2 for each design flow. Conditions for the six unique grid configurations for Location 2 are shown in Table 5.


Table 5. Configuration for Location 2 Alternative Designs.

Scenario White Ditch Diversion Flow Rate (cfs) Number of Culverts at Each Location Total Culvert Cross-Sectional Area (ft2)
1 5,000 4 to 8 367
2 10,000 6 to 12 551
3 15,000 10 to 20 918
4 35,000 15 to 30 1377
5 70,000 30 to 60 2755
6 100,000 50 to 100 4592



Figure 6. CMS Grid bathymetry in vicinity of Alternative Location 2.

A 2-D CMS-Flow model was developed and calibrated to evaluate each design. Details of the model configuration and calibration can be found in URS (2010). The model domain extends about 60 km along the NW-SE directions and about 30 km along the SW-NE direction, and includes the Mississippi River levees, the Mississippi River-Gulf Outlet (MRGO) channel, and other features. The size of the CMS grid cells ranges from 24 to 600 m with the fine grid along the White Ditch (Mississippi River) and the coarse grid in the Gulf of Mexico. Figure 6 shows a view of the CMS grid bathymetry in the vicinity of the Location 2 alternative diversion. The channels and channel elves are evident. The grid includes specification of the culverts per the alternative design schematics. The culverts were assumed to have a circular cross-section with 3 foot diameter, and 10 foot length.


The CMS model boundary conditions included tidal elevations at the offshore boundary, freshwater flow at the Caernarvon Diversion, and freshwater inputs at the proposed White Ditch diversion. Tide data from the U.S. Geological Survey (USGS) station (7374527) at Northeast Bay Gardene near Point-A-LA-Hache, LA was used as the tide boundary. Freshwater flows were measured by the New Orleans District, USACE, and were used at the Caernarvon flow boundary.


Figure 7shows a time-series of snap shots of the freshwater flowing from the diversion, through the diversion channels and into the wetlands. The flow through the culverts is evident at each culvert location as indicated by the growing freshwater area.


Figure 7. CMS Simulation results showing freshwater discharging through culverts.


Additional Information

This CHETN was prepared and funded under the Coastal Inlets Research Program (CIRP) and was written by Dr. Christopher W. Reed (Chris_Reed@URSCorp.com) of URS Corporation. The CIRP Program Manager, Dr. Julie D. Rosati (Julie.D.Rosati@usace.army.mil), the assistant Program Manager, Dr. Nicholas C. Kraus, the Chief of the Coastal Engineering Branch at CHL and Alejandro Sanchez reviewed this CHETN. Files for the example may be obtained by contacting the author.


References

  • Buttolph, A. M., C. W. Reed, N. C. Kraus, N. Ono, M. Larson, B. Camenen, H. Hanson, T. Wamsley, and A. K. Zundel, A. K. 2006. Two-dimensional depth-averaged circulation model CMS-M2D: Version 3.0, Report 2, sediment transport and morphology change. Coastal and Hydraulics Laboratory Technical Report ERDC/CHL-TR-06-7. Vicksburg, MS: U.S. Army Engineer Research and Development Center.
  • Bodhaine, G.L., 1982, "Measurement of Peak Discharge at Culverts by Indirect Methods," Techniques of Water Resources Investigations of the United States Geological Survey, Book 3, Chapter A3, U.S. Geological Survey, WA.
  • Militello, A., Reed, C.W., Zundel, A.K., and Kraus, N.C. 2004. Two-Dimensional Depth-Averaged Circulation Model M2D: Version 2.0, Report 1, Technical Documentation and User’s Guide, ERDC/CHL TR-04-2, U.S. Army Research and Development Center, Coastal and Hydraulics Laboratory, Vicksburg, MS.
  • URS. 2010. USACE White Ditch evaluation and design – hydrodynamic and salinity transport modeling. URS Corporation, Tallahassee, FL.

Documentation Portal