CMS-Flow Graphical Interface

The CMS-Flow graphical interface includes tools to assist with creating, editing, and debugging a CMS-Flow model. The CMS-Flow interface exists in the Cartesian Grid Module. The Map Module also provides flexibility when creating the grid.

CMS-Flow Menu

The interface consists of tools to create the grid, a CMS-Flow menu with model specific commands and visualization tools for analyzing the data sets computed by the model. The menu includes the following commands:

• Assign BC... (Boundary Condition)
• Delete BC...
• Cell Attributes...
• Merge Cells
• Model Check...
• Model Control...
• Run CMS-Flow...

Setting Up/Editing a Model

Grid Creation

A grid for CMS-Flow consists of varying sized rectangular cells. Each cell defines the depth from a fixed datum to the bottom of the water column at the centroid of the cell. CMS-Flow computes the water level at the cell centroid, and the flow velocity across each cell face. A grid may be created in one of two ways including:

• Through the Cartesian Grid module. This option allows for the creation of a simple grid consisting of cells of uniform size (they may be rectangular, but all the same size). See Creating 2D Cartesian Grids for more information. This grid may be edited in the Cartesian Grid module (see Editing 2D Grids).
• Using a CMS-Flow Coverage in the Map Module. This method results in a grid that can be edited with all of the tools available in the Cartesian Grid module, but also allows flexibility in two ways:
  • Refine points may be created to specify cell resolution in one or both directions at specific locations inside the domain. This allows areas of high concern, and high variability, such as in the mouth of an inlet to be defined with specified high resolution, which transitions to lower resolution in areas away from these regions.
  • The grid frame, with the grid definition are saved and can be copied and edited to create variations of grid resolution and coverage.

Boundary Conditions

All numeric models require boundary condition data. In CMS-Flow, boundary conditions are defined on cell strings.

Cell Strings

For CMS-Flow, a cell string consists of a series of contiguous or adjacent cells. This means the cells share at least a corner and usually an edge. When SMS creates a grid, it also creates cell strings around the computational domain. This consists of open ocean cells along the edge of the domain as well as the last ocean cells adjacent to the land. SMS will create one cell string for each continuous section of ocean along the grid boundary, one cell string for each section of coastline, and one cell string for each island. Each cell string may be assigned an attribute to describe the type of boundary condition applied at that location. If no specification is made, the default boundary condition is a closed boundary (no flow is allowed across this boundary). This is typically the case for coastline and island cell strings. These cell strings are actually not even required for CMS-Flow, but are useful when using CMS-Flow output in a Particle Tracking Model (PTM) simulation. Cell strings may be split into multiple cell strings by selecting the cell where the break is desired and selecting the "Split" command from the Cellstring menu. Cell strings may be merged by selecting two (or more) cellstrings that connect in a continuous line, and selecting the "Merge" command from the Cellstring menu.

Assigning Boundary Conditions

The user assigns a boundary condition by activating the Select Cellstring tool, selecting the cell string, and then selecting the Assign BC... command from the menu. This invokes the CMS-Flow Boundary Conditions dialog and allows the user to define the conditions along the cell string. Multiple cell strings may be selected and assigned at the same time, but this is not common. Typically, the boundary conditions will only be applied to cell strings along the edge of the domain, but may be applied to cell strings on the interior if a portion of the domain is to be excluded from computation (such as cutting off a portion of a bay) for computational efficiency. Boundary condition types supported by CMS include:

• Land - This is the default condition and indicates that no flow will cross this boundary.
• Flow rate-forcing - This allows the user to specify an inflow rate (flow in cubic meters/second at each cell). This can be used to represent a river flowing into the domain.
• WSE-forcing - This allows the user to specify the water surface elevation as a function of time for the cellstring. Options include specifying a single curve (water level -vs- time) and all the cells will have the same water level at the specified time and extracting individual curves for each cell either from a regional tidal database (ADCIRC database) or from a regional (larger) circulation model.
• Tidal constituent-forcing - This allows the user to specify the water surface as a function of the principal tidal constituents around the domain. When this option is selected, the user must specify which constituents (along with their amplitudes and phases) in the Model Control dialog. All cells in the tidal cell strings will be forced with the same water levels.
• WSE and Velocity-forcing - This option allows the user to extract both water levels and velocity values for each cell in the cellstring from a regional model. This requires a regional model to extract from.

Cell Attributes

The user may select cells and assign attributes to them using Select Cell tool and two commands from the CMS-Flow menu.

If a cell is selected, its bathymetric depth may be edited using the "Z" edit field at the top of the screen.

For any selected cells, the Assign Cell Attributes command allows the user specify the cell as water or land, and if it is water, specify that it is an observation cell. This option instructs the model to output data at a higher frequency at this location for analysis after the simulation is complete.

When entire adjacent rows or columns are selected, they may be merged to decrease resolution in this area of the domain. (Warning, this operation deletes all cell strings, so all boundary condition specification would be lost if this operation is performed. Make sure you do this type of operation during grid construction.)

Model Check

Whenever the user issues the Model Check command, and just before launching an analysis, SMS performs a check on the model. If conditions are detected that are out of the ordinary or recommended range, warnings are given with suggestions to correct the problem. If serious problems are detected, errors are reported, again with suggestions.

Model checks include checking on the aspect ratio of the cells, ensuring that compatible boundary conditions are specified, and ensuring that model parameters are within acceptable ranges.

The model check is not all inclusive. Just because a model passes the model check does not guarantee the model will run and produce viable solutions.

Model Control

The CMS-Flow Model Control Dialog is used to setup the options that apply to the simulation as a whole. These options include time controls, run types, output options, global parameters, print options and other global settings.

CMS-Flow Model Control page

Running the Model

The CMS-Flow files are written automatically with the SMS project file or can be saved separately using the File | Save CMS-Flow or File | Save As menu commands. See the CMS-Flow publications from ERDC for more information on the files used for the CMS-Flow run.

CMS-Flow can be launched from SMS using the CMS-Flow | Run CMS-Flow menu command. A check of some of the common problems called the Model Checker is done each time the model is launched, or by selecting the CMS-Flow | Model Check menu command.

Related Topics

• Hard Bottom
• Observation Cells
• Cell Attributes
• Advanced Cards
• Salinity
• Create a 2D Cartesian grid