CMS-Flow Model Parameters: Difference between revisions

From CIRPwiki
Jump to navigation Jump to search
(Created page with "==Model Parameters== [[Image:Shark_Fig21.PNG|thumb|right|300px|Figure 1. ''CMS-Flow Model Control'' : ''Model Parameters'' tab for specifying time series output of CMS-Flow cal...")
 
(Created page with ==Model Parameters== [[Image:Shark_Fig21.PNG|thumb|right|300px|Figure 1. ''CMS-Flow Model Control'' : ''Model Parameters'' tab for specifying time series output of CMS-Flow cal...)
Line 3: Line 3:
All of the CMS-Flow model parameters,  settings, and output options are controlled from the ''CMS-Flow Model Control'' window (Figure 1). The window also has a section for Advanced Cards in  which new features which have not been incorporated into the SMS interface yet or more advanced model features more experienced users.
All of the CMS-Flow model parameters,  settings, and output options are controlled from the ''CMS-Flow Model Control'' window (Figure 1). The window also has a section for Advanced Cards in  which new features which have not been incorporated into the SMS interface yet or more advanced model features more experienced users.


<br style="clear:both" />
br style=clear:both /
1. Click on ''CMS-Flow'', ''Model Control'', and set each tab as the following figures (Figures 21-25),
1. Click on ''CMS-Flow'', ''Model Control'', and set each tab as the following figures (Figures 21-25),


2.  For ''Time Control'', change the ''Simulation duration'' to 744.0  hours, ''Ramp'' to 24 hors, and ''Hydrodynamic time step'' to 1.0 (must  be tested by running CMS-Flow only),
2.  For ''Time Control'', change the ''Simulation duration'' to 744.0  hours, ''Ramp'' to 24 hors, and ''Hydrodynamic time step'' to 1.0 (must  be tested by running CMS-Flow only),


<br style="clear:both" />
br style=clear:both /
[[Image:Shark_Fig22.PNG|thumb|right|300px|Figure  22. ''''''''CMS-Flow Model Control'''''''': ''''''''Transport''  ''''''tab for specifying time series output of CMS-Flow calculated  datasets.]]
[[Image:Shark_Fig22.PNG|thumb|right|300px|Figure  22. ''''''''CMS-Flow Model Control'''''''': ''''''''Transport''  ''''''tab for specifying time series output of CMS-Flow calculated  datasets.]]


3. For ''Transport Parameters'', change the  ''Transport rate'' to 1.0 and the ''Morphologic time'' step to 10  seconds, check ''Use non-equilibrium transport'' and set the parameters  as those in Figure 22,
3. For ''Transport Parameters'', change the  ''Transport rate'' to 1.0 and the ''Morphologic time'' step to 10  seconds, check ''Use non-equilibrium transport'' and set the parameters  as those in Figure 22,


<br style="clear:both" />
br style=clear:both /
[[Image:Shark_Fig23.PNG|thumb|right|300px|Figure  23.  ''''''''CMS-Flow Model Control'''''''': ''''''''Output'' ''''''tab  for specifying time series output of CMS-Flow  calculated datasets.]]
[[Image:Shark_Fig23.PNG|thumb|right|300px|Figure  23.  ''''''''CMS-Flow Model Control'''''''': ''''''''Output'' ''''''tab  for specifying time series output of CMS-Flow  calculated datasets.]]


Line 20: Line 20:
5. Set ''Output Times 2'' for  ''Morphology'' output at a 3-hr interval, by changing the ''Increment''  to 3.0 and adding, and selecting that on the drop down menu for  Morphology,
5. Set ''Output Times 2'' for  ''Morphology'' output at a 3-hr interval, by changing the ''Increment''  to 3.0 and adding, and selecting that on the drop down menu for  Morphology,


<br style="clear:both" />
br style=clear:both /
[[Image:Shark_Fig24.PNG|thumb|right|300px|Figure  2. ''CMS-Flow Model Control'' ''Output'' tab  for specifying time series output of CMS-Flow  calculated datasets.]]
[[Image:Shark_Fig24.PNG|thumb|right|300px|Figure  2. ''CMS-Flow Model Control'' ''Output'' tab  for specifying time series output of CMS-Flow  calculated datasets.]]


6.  The same can be done for ''Transport'', which should normally be set to  an ''Increment'' on the order of the tide or wave time series  (<nowiki><</nowiki>3 hr; typically 0.5-1.5hr), and it is  suggested that it be set to 1-hr output increment for ''Output Times 3  ''(Figure 24), ''OK''.
6.  The same can be done for ''Transport'', which should normally be set to  an ''Increment'' on the order of the tide or wave time series  (nowiki/nowiki3 hr; typically 0.5-1.5hr), and it is  suggested that it be set to 1-hr output increment for ''Output Times 3  ''(Figure 24), ''OK''.


<br style="clear:both" />
br style=clear:both /
[[Image:Shark_Fig25.PNG|thumb|right|300px|Figure  3. ''''''''CMS-Flow Model Control'''''''': ''''''''Advanced''  ''''''tab for specifying any advanced cards or modifications to  CMS-Flow.]]
[[Image:Shark_Fig25.PNG|thumb|right|300px|Figure  3. ''''''''CMS-Flow Model Control'''''''': ''''''''Advanced''  ''''''tab for specifying any advanced cards or modifications to  CMS-Flow.]]


7. For the ''Advanced Tab'', the option for  using multiple threads or processors (in all caps, OPENMP_PROCESSORS  2.0) can be set up following Figure 36, ''OK''.
7. For the ''Advanced Tab'', the option for  using multiple threads or processors (in all caps, OPENMP_PROCESSORS  2.0) can be set up following Figure 36, ''OK''.


<br style="clear:both" />
br style=clear:both /

Revision as of 15:44, 16 January 2011

Model Parameters

Figure 1. CMS-Flow Model Control : Model Parameters tab for specifying time series output of CMS-Flow calculated datasets.

All of the CMS-Flow model parameters, settings, and output options are controlled from the CMS-Flow Model Control window (Figure 1). The window also has a section for Advanced Cards in which new features which have not been incorporated into the SMS interface yet or more advanced model features more experienced users.

br style=clear:both / 1. Click on CMS-Flow, Model Control, and set each tab as the following figures (Figures 21-25),

2. For Time Control, change the Simulation duration to 744.0 hours, Ramp to 24 hors, and Hydrodynamic time step to 1.0 (must be tested by running CMS-Flow only),

br style=clear:both /

Figure 22. CMS-Flow Model Control: Transport 'tab for specifying time series output of CMS-Flow calculated datasets.

3. For Transport Parameters, change the Transport rate to 1.0 and the Morphologic time step to 10 seconds, check Use non-equilibrium transport and set the parameters as those in Figure 22,

br style=clear:both /

Figure 23. CMS-Flow Model Control: Output 'tab for specifying time series output of CMS-Flow calculated datasets.

4. Set the time series output for the water surface elevation and velocity to the same output interval of 30 minutes, similar to Figure 23,by highlighting Output Times 1, setting the Start Time to 0.0 hr, Increment to 0.5 hr, and End Time to 744.0 hr, and clicking Add,

5. Set Output Times 2 for Morphology output at a 3-hr interval, by changing the Increment to 3.0 and adding, and selecting that on the drop down menu for Morphology,

br style=clear:both /

Figure 2. CMS-Flow Model Control Output tab for specifying time series output of CMS-Flow calculated datasets.

6. The same can be done for Transport, which should normally be set to an Increment on the order of the tide or wave time series (nowiki/nowiki3 hr; typically 0.5-1.5hr), and it is suggested that it be set to 1-hr output increment for Output Times 3 (Figure 24), OK.

br style=clear:both /

Figure 3. CMS-Flow Model Control: Advanced 'tab for specifying any advanced cards or modifications to CMS-Flow.

7. For the Advanced Tab, the option for using multiple threads or processors (in all caps, OPENMP_PROCESSORS 2.0) can be set up following Figure 36, OK.

br style=clear:both /

Retrieved from "https://cirpwiki.info/index.php?title=CMS-Flow_Model_Parameters&oldid=7194"