CMS-Flow Sediment Transport

SMS 10.1

The sediment transport controls are located in the Transport section of the CMS-Flow Model Control window as shown in the figure below. The sediment transport is activated by going to the Transport section of the CMS-Flow Model Control and checking the box labeles Calculate sediment transport. The CMS card used to turn on or off the sediment transport is described in the table below.

Card	Arguments	Default	Range	Description
CALC_SEDIMENT_TRANSPORT	CHARACTER	OFF	ON | OFF	Turns on or off the sediment transport calculation.

Transport model

There are currently three sediment transport models available in CMS: (1) Equilibrium total load, (2) Equilibrium bed load plus advection-diffusion for suspended load, and (3) Non-equilibrium total load. The first two models are selected by unchecking the checkbox which says "Use non-equilibrium transport" and selecting either "Total load" for the first model, or "Advection-diffusion" for the second next to input item named "Formulation". The third model is selected by checking the box "Use non-equilibrium transport".

Card	Arguments	Default	Range	Description	Versions
SED_TRAN_FORMULATION	CHARACTER	NET	WATANABE | LUND_CIRP | A-D | NET	Selects the sediment transport model.	>1.0
SED_TRAN_CALC_INTERVAL	REAL		greater or equal to hydro time step for explicit scheme, or equal hydro time step for implicit scheme	Time step used for transport equation
MORPH_UPDATE_INTERVAL	REAL		greater or equal to hydro time step for explicit scheme, or equal hydro time step for implicit scheme	Time step used for updating bed elevation

Note that the when selecting the equilibrium total load model, the SED_TRAN_FORMULATION card is set to either WATANABE or LUND_CIRP depending on the transport formula chosen. When selecting the equilibrium A-D model, the transport formula is specified through the concentration profile formula (described below).

1. Equilibrium Total load

In this model, both the bed load and suspended load are assumed to be in equilibrium. The bed change is solved using a simple mass balance equation known as the Exner equation. More information on the this model can be found here.

2. Equilibrium Bed load plus Advection-Diffusion Suspended Load

Calculations of suspended load and bed load are conducted separately. The bed load is assumed to be in equilibrium and is included in the bed change equation while the suspended load is solved through the solution of an advection-diffusion equation. Actually the advection diffusion equation is a non-equilibrium formulation, but because the bed load is assumed to be in equilibrium, this model is referred to the "Equilibrium A-D" model.

More information on the this model can be found here.

3. Non-equilibrium Total Load

The non-equilibrium sediment transport algorithm (NET) simulates non-cohesive, single size sediment transport and bed change using a Finite Volume method and includes advection, diffusion, hiding and exposure, and avalanching. NET sediment transport is calculated with a non-equilibrium bed-material (total load) formulation. In this approach, the suspended- and bed-load transport equations are combined into a single equation and thus there is one less empirical parameter to estimate (adaptation length).

Additional information on NET can be found here.

All of the previously mentioned models account for hard bottom and effect of the bed slope on bed load.

Transport Formula

The nearbed sediment concentation or concentration capacity are calculated with one of the following transport formula:

1. Lund-CIRP (2006)
2. Van Rijn (1998)
3. Watanabe (1987)
4. Soulsby-van Rijn (1997) (>=V4.0)

Card	Arguments	Default	Range	Description
NET_TRANSPORT_CAPACITY	CHARACTER	LUND-CIRP	LUND-CIRP | VAN_RIJN | WATANABE | SOULSBY	Selects the transport formula. Note that SOULSBY is only available in v>=4.0
TRANSPORT_FORMULA	CHARACTER	LUND-CIRP	LUND-CIRP | VAN_RIJN | WATANABE | SOULSBY	Selects the transport formula. Note that SOULSBY is only available in v>=4.0.
SED_TRANS_FORMULATION	CHARACTER	LUND-CIRP	LUND-CIRP | A-D | WATANABE | NET	Selects the transport formula for the equilibrium total load model. Does not specify the transport formula for the equilibrium A-D and non-equilibrium total load models.
CONCENTRATION_PROFILE	CHARACTER	LUND-CIRP	LUND-CIRP|EXPONENTIAL| ROUSE| VAN_RIJN	Selects the concentration profile to be used either in the equilibrium A-D or total load nonequilibrium models.
A_COEFFICIENT_WATANABE	REAL	0.1	0.05-0.5	Empirical coefficient which goes into the Watanabe transport formula.

Scaling Factors

Transport Scaling Factors

The bed and suspended transport scaling factors multiply directly by the transport capacity or near-bed sediment concentration calculated from the transport formula. These factors should be used to calibrate sediment transport rates and due to the large uncertainty in the transport formula, it is generally acceptable to use scaling factors in the range of 0.5-2.0.

Card	Arguments	Default	Range	Description
BED_LOAD_SCALE_FACTOR	REAL	1.0	0.5-2.0	Calibration factor for bed load transport capacity formula
SUSP_LOAD_SCALE_FACTOR	REAL	1.0	0.5-2.0	Calibration factor for suspended load transport capacity formula

Morphologic Scaling Factor

The morphologic scaling factor is directly multiplied by the calculated bed change at every time step and is intended as a means of speeding up the computational time. It is only recommended for periodic boundary conditions or conditions that do not change rapidly over time.

Card	Arguments	Default	Range	Description
MORPH_ACCEL_FACTOR	REAL	1.0	1-100	Morphologic acceleracion factor. Directly multiplies by calculated bed change.

Sediment Characteristics

Card	Arguments	Default	Range	Description	Versions
SEDIMENT_POROSITY	REAL	0.4	0-1	Sets the sediment porosity
SEDIMENT_DENSITY	REAL	2650	none	Sets the sediment density in kg/m^3
SEDIMENT_FALL_VELOCITY	REAL	none	4.0e-4 - 0.4	Sets the sediment fall velocity to a constant in m/s	v>=3.5

Bedslope term

Card	Arguments	Default	Range	Description	Versions
SLOPE_COEFFICIENT	REAL	1.0	0-5	Bed slope coefficient which controls enters a diffusion term which moves sediment down slope

Boundary and Initial Conditions

Card	Arguments	Default	Range	Description	Versions
NET_LOADING_FACTOR	REAL	1.0	0.5-2.0	Used to specify under- or overloading at sediment inflow boundaries. Only for NET.	3.5=>v<=4.0
SEDIMENT_INFLOW_LOADING_FACTOR	REAL	1.0	0.5-2.0	Used to specify under- or overloading at sediment inflow boundaries.	>=4.0
CALC_MORPH_DURING_RAMP	CHARACTER	ON	ON | OFF	Determines whether to calculate the morphology change during the ramp period	v>=3.5

Advanced

Card	Arguments	Default	Range	Description	Versions
HIDING_EXPOSURE_COEFFICIENT	REAL	0.7	0.6-1.0	Hiding and exposure coefficient.	v>=3.5
SCHMIDT_NUMBER	REAL	1.0	none	Controls the sediment mixing strength	v>=4.0