Wave NoCards

The *.std has a maximum of 25 parameters - the first 15 parameters are more the basic ones as described in the CMS-Wave Technical Report (CHL-TR-08-13) while the remaining 10 parameters are relatively new for advanced CMS-Wave features.

Table 1. CMS-Wave parameters in STD file

Number	Variable	Argument Type	Options/Range	Description
1	iprp	INTEGER	0 - waves and wind input in *.eng 1 - waves only, neglect wind input in *.eng -1 - fast mode (wind and spectra) -2 - fast mode with spectra only.	Wave propagation mode.
2	icur	INTEGER	0 - no current input 1 - with current input *.cur 2 -with *.cur, use only the 1st set current data	Current interaction
3	ibk	INTEGER	0 - no wave breaking output 1 - output breaking indices 2 - output energy dissipation rate	Wave breaking output option
4	irs	INTEGER	0 - no wave radiation stress calculation or output 1 - calculate and output radiation stresses 2 - calculate and output radiation stresses plus setup/max-water-level	Radiation stress and runup options.
5	kout	INTEGER	>= 0	Number of special wave output location, output spectrum in *.obs and parameters in selhts.out
6	ibnd	INTEGER	0 - no input a parent spectrum *.nst 1 - read *.nst, averaging input spectrum 2 - read *.nst, spatially variable spectrum input	Nesting option.
7	iwet	INTEGER	0 - allow wet/dry, default 1 - without wet/dry -1 allow wet/dry, output swell and local sea files	Wetting and drying options.
8	ibf	INTEGER	0 - no bottom friction calc 1 - constant Darcy-Weisbach coef, c_f 2 -read variable c_f file, *.fric 3 - constant Mannings n 4 - read variable Mannings n file, *.fric	Bottom friction option.
9	iark	INTEGER	0 - without forward reflection 1 - with forward reflection	Forward reflection option.
10	iarkr	INTEGER	0 - without backward reflection, 1 - with backward reflection	backward reflection option.
11	akap	REAL	0.0<=akap<=4.0	Diffraction intensity coefficient.
12	bf	REAL	>=0	constant bottom friction coef c_f or n (typical value is 0.005 for c_f and 0.025 for Mannings n)
13	ark	REAL	0.0<=ark<=1.0	Constant forward reflection coef, global specification (0 for zero reflection, 1 for full reflection).
14	arkr	REAL	0.0<=arkr<=1.0	Constant backward reflection coef, global specification (0 for zero reflection, 1 for full reflection)
15	iwvbk	INTEGER	0 - Goda-extended 1 - Miche-extended 2 - Battjes and Janssen 3 - Chawla and Kirby)	Option for the primary wave breaking formula.
16	nonln	INTEGER	0 - none, default 1 - nonlinear wave-wave interaction	Nonlinear wave-wave interaction
17	igrav	INTEGER	0 - none, default 1 - infra-gravity wave enter inlets	Infragravity waves option.
18	irunup	INTEGER	0 - none, default 1 - automatic, runup relative to absolute datum 2 - automatic, runup relative to updated MWL	Runup option.
19	imud	INTEGER	0 - Mud dissipation on, default 1 - none	Mud dissipation option. The kinematic viscosity is specified in mud.dat in units of m2/sec
20	iwnd	INTEGER	0 - Spatially variable wind on, default 1 - None	Spatially variable wind field option. The winds are specified in wind.dat in units of m/s and in the reference frame of the CMS-Wave grid
21	isolv	INTEGER	0 - GSR solver, default 1 - ADI	Matrix solver for CMS-Wave.
22	ixmdf	INTEGER	0 - output ascii, default 1 - output xmdf	XMDF input and output options.
23	iproc	INTEGER	>=0	Number of threads for parallel computing. Optimum number is approximately equal to the total row number divided by 300. Only for isolv = 0.
24	iview	INTEGER	0 - half-plane, default 1 - full-plane 2 - full-plane with reverse spectra	Half-plane/full-plane option. users can provide additional input wave spectrum file wave.spc (same format as the *.eng) along the opposite side boundary an imaginary origin for wave.spc at the opposite corner; users can rotate the CMS-Wave grid by 180 deg in SMS to generate this wave.spc
25	iroll	INTEGER	0 - disable Roller, default 1,2,3,4 - enabled with increasing effectiveness	Valid in the surf zone in cell with resolution <= 10 m

Among these 24 parameters in *.std, the first 6 parameters are always required in CMS-Wave and the remaining ones starting any parameter after the 6^th will be assigned to the default values if not provided in the *.std. The more specific use and options associated with each of these 1^st to 24^th parameters are given below.

• Full-plane – In this mode, CMS-Wave performs two half-plane runs in the same grid. The first

run is in the half-plane with the principle wave direction toward the shore. The second run is in the seaward half-plane. Upon the completion of the second run, two half-plane results are combined to one full-plane solution. Because the run time for the full-plane is approximately twice of the regular half-plane, users shall consider the full-plane mode only if the full-plane features like wave generation and propagation in a bay or around an island. An example is to run the Shark River wave case, 2009.sim, in the full plane (modify 2009.std).

Go Back to Model Parameters